Your Shopping Cart

It appears that your cart is currently empty!

CONTINUE SHOPPING

DIY: HOW TO BUILD A PORTABLE SKI OR SNOWBOARD WAXING TABLE

by Blog Updates |

Friends of the tiny apartment, the strict landlady, the fourth-floor walk-up, we hear you. A garage is sketched into the blueprint of your someday life, but right now you’re living in a studio jammed with gear.

How can you wax your own skis and snowboards?

The answer is simple: Build a self-contained waxing table that folds up and won’t drip on the carpet. It’s genius! You can put it on any flat surface, like the kitchen table. As you scrape your skis or snowboard, all the wax falls into the box. Two cutout slats underneath allow you to brush the wax from the table into the garbage. Fold it up and store it away with the rest of your gear. Sounds rad, right? Then let’s get to work.

What You’ll Need:

Supplies:

  • 4′ x 8′ sheet of ½” plywood
  • 1 16” piano hinge
  • 2 buckle latches
  • 12 anti-skid pads
  • Wood glue
  • Wood screws (1/2”, ¾”)
  • Old bike tube
  • 8 5/16 x 2” carriage bolts with washers and wing nuts
  • 2 D-rings and mounts

Tools:

  • Screwdriver
  • Tape measures
  • Drill with small bit
  • Pencils
  • Construction square
  • Skill saw
  • Small handsaw
  • Safety glasses

Download the waxing table supplies list and cut sheet and get started: Portable Ski or Snowboard Waxing Table.

How to Build It:

Step 1

waxing table

Transfer your measurements from the cut sheet to the plywood. Make sure to account for “kerf,” so everything stays square for assembly. (Kerf is the divergence between saw teeth, and it defines the width of the cut.) Plan your cuts to break down the plywood in the least amount of cuts. If you don’t own a saw, most hardware stores offer cutting services. If you plan to have the hardware store do the cutting, you’ll want to provide a cut list and a diagram.

Step 2

DIY ski waxing box

Start by assembling the bottoms and end caps of the boxes, followed by the two sides. If you are not using self-drilling screws, you should pre-drill holes for best results. Screw and glue all seams.

Step 3

diy ski waxing box

Install inner pieces to create slots that are spaced a half-inch apart. We used screws, not glue, in case we wanted to change the spacing later. (Depending on your bindings, how you space these slots are optional; we put two slots on each box for flexibility.)

Step 4

diy ski waxing box

Install the piano hinge, making sure to center the hinge in the seam of the two box halves for easy folding.

Step 5

diy ski waxing box

Install anti-skid pads to the bottoms and hinge sides of both boxes. Offset the anti-skid pads on the hinges so they don’t hit each other when the box is open.

Step 6

diy ski waxing box

Install the buckles.

Step 7

diy ski waxing box

Install the side braces. Clamp and drill through the brace and the side of the box, then install and glue carriage bolts into the brace. Mark the braces and the box sides they relate to so it’s easier to match them up later.

Step 8

diy ski waxing box

Assemble the ski/snowboard supports. Measure, cut and install the bike tube for ski/snowboard supports. We added an optional radius cut to the bottom of the supports to allow wax to be brushed through for easier cleanup.

Step 9

diy ski waxing box

Cut out the handles and wax slot. The size of your slot is optional; we chose the width of our small hand broom to make it easier to brush the wax out of the box.

Step 10

diy ski waxing box

Install D-rings. We positioned ours just under the ski brake so we could hold down the ski and brake at the same time.

Step 11

diy ski waxing box

Sand and finish.

You’re all done! Now get stoked for the snow with a Pray for Snow party, complete with ski and snowboard waxing station. Your buddies will be impressed!

Source: REI